从限额设计谈投资控制

文章根据设计阶段投资控制的现状及存在问题,提出只有在设计行业全面推行限额设计,深化设计阶段的投资控制工作,才能从根本上体现全过程投资控制的理念,提高投资控制效果,节约建设工程总投资。     

高加速应力试验及极限应力试验综述

介绍了高加速应力试验(HAST)及极限应力试验(limit test)的基本概念和相关背景,列举了当前国内外一些常用的技术方法、工程应用状况、试验模型及分析方法、试验剖面的建立及失效机理的确定等。指出了高加速应力试验及极限应力试验要注意的问题,并对它们的发展动向作了简单的预测。     

圆管流动的二次转捩

利用直接数值模拟方法求解N-S方程来研究空间发展的圆管转捩,计算中雷诺数Re选定为3000。在局部壁面引入的周期性吹吸(PSB)扰动作用下,圆管中首先出现了塞流结构,并向下游迁移,同时有稳定的流向条带结构形成;在塞流结构离开计算域后,随着扰动的不断发展,流向条带结构逐渐破裂失稳,圆管流动出现了第二次转捩,这是一种新的转捩形式,我们称之为“二次转捩”。     

热轧带钢连续冷却过程中相变体积分数的计算

基于相变动力学原理 ,在充分考虑变形对相变影响的情况下研究了奥氏体向铁素体、珠光体和贝氏体相变的动力学。探索了热轧带钢连续冷却过程中相变体积分数的计算方法。用此方法进行的计算机模拟与实验结果相当吻合。     

OCT-M 汽油选择加氢工艺工业应用

介绍了OCT-M汽油选择性加氢技术在汽油加氢装置的应用情况。对影响加氢汽油质量的主要因素进行了分析，提出了降低加氢过程汽油辛烷值损失、降低大分子硫醇生成的优化措施，并针对存在的问题提出了相应的改进建议。     

Design of High Speed AWGN Communication Channel Emulator

This paper presents a method for designing a high accuracy white gaussian noise generator suitable for communication channel emulation. The proposed solution is based on the combined use of the Box-Muller method and the central limit theorem. The resulting architecture provides a high accuracy AWGN with a low complexity architecture for a digital implementation in FPGA. The performance is studied by means of MATLAB simulations and various complexity figures are given.     

NUMERICAL SIMULATIONS OF 2D PERIODIC UNSTEADY CAVITATING FLOWS

1. INTRODUCTION Cavitation is a natural phenomenon especially existing in liquids. A cavitating flow generally involves a large number of vapor structures such as bubbles or vortices which are convecting downstream. When they reach high pressure zones, th…     

钢筋混凝土结构正截面强度计算理论的应用

简述了钢筋混凝土正截面强度计算理论的发展历程，介绍了其计算理论的特点及其存在的问题，并对今后需要进一步研究的问题进行了展望，为工程设计提供参考。     

Design optimization of 3D steel structures: Genetic algorithms vs. classical techniques

In this paper an elitist genetic algorithm (GA) developed by the authors is compared with common commercial solutions for complex structural optimization. After its prior validation on two-dimensional (2D) structures, the GA was tuned and improved in order to obtain structural elements with minimum weights that satisfy the ultimate limit states of the applicable building code. Subsequently, the same spatial structures were optimized using a commercial structural analysis program. Finally, the cost and weight improvements obtained using the GA, although at a higher computational cost, are discussed.     

Preparation and properties of silicone‐containing poly(methyl methacrylate) gels

Poly(methyl methacrylate) (PMMA) gels with varying amounts of silicone and solvent and constant amounts of crosslinker were prepared by solution free radical crosslinking copolymerization of methyl methacrylate (MMA), ethylene glycol dimethacrylate (EGDM), tetraethoxysilane (TEOS) and vinyltriethoxysilane (VTES) comonomer systems. They were then studied in benzene at a total monomer concentration of 3.5 mol L^?1 and 70 °C. The conversion of monomer, volume swelling ratio, weight fraction and gel point were measured as a function of the reaction time, silicone concentration and benzene content up to the onset of macrogelation. Structural characteristics of the gels were examined by using equilibrium swelling in benzene, gel fraction and Fourier‐transform infrared (FTIR) analysis. The morphology of the copolymers was also investigated by SEM. Based on the obtained results, it was concluded that the FTIR data did not have the capacity to show the presence of the VTES or TEOS moiety in these kinds of copolymers. On the other hand, the variation of weight fraction of gel, W_g, and its equilibrium volume swelling ratio in benzene, q_v, exhibited the same behaviour as that of MMA/EGDM copolymers. Also, the dilution of the monomer mixture resulted in an increase in the gel point and swelling degree and a decrease in the percent of conversion and gel fraction. Finally, TEOS is not an ideal silicone compound for reaction in the MMA/EGDM copolymerization system, whereas VTES is a suitable silicone comonomer for this system and it has been proved useful. Copyright © 2005 Society of Chemical Industry